Toshiba HX7+ ASD, Installation & Operation Manual

Page: 255 / 257

246 HX7+ ASD Installation and Operation Manual
RS232/RS485 Master Output, 188
RS232/RS485 Response Delay Time, 188
RS232/RS485 Wire Count, 188
RS485, 33
Run Frequency, 118
Run Frequency Hysteresis, 118
Run Key, 39
RX, 28
RX Bias Adjust, 150
RX Gain Adjust, 151
RX Input Speed Control Setup, 108
RX Input Torque Control Setup, 108
RX Speed Frequency #1, 109
RX Speed Frequency #2, 109
RX Speed Reference #1, 108
RX Speed Reference #2, 109
RX terminal, 30
RX Torque Reference Setpoint #1, 109
RX Torque Reference Setpoint #2, 110
RX2 Bias Adjust, 151
RX2 Gain Adjust, 151
RX2 Input Speed Control Setup, 111
RX2 Input Torque Control Setup, 111
RX2 Speed Frequency #1, 112
RX2 Speed Frequency #2, 112
RX2 Speed Reference #1, 111
RX2 Speed Reference #2, 112
RX2 Torque Reference Setpoint #1, 112
RX2 Torque Reference Setpoint #2, 113
S
S/L2, 24
S1, 28
S1 – S4 Input Terminal Delay, 91
S1 Input Terminal Assignment, 85
S1 terminal, 29
S2, 28
S2 Input Terminal Assignment, 85
S2 terminal, 29
S3, 28
S3 Input Terminal Assignment, 85
S3 terminal, 29
S4, 28
S4 Input Terminal Assignment, 85
S4 terminal, 29
S5 – S16 Input Terminal Delay, 91
S5 Input Terminal Assignment, 86
S6 Input Terminal Assignment, 86
S7 Input Terminal Assignment, 86
Scrolling Monitor Select, 69
Short Circuit Current Rating, 230
Short Circuit Detect Pulse, 64
Short Circuit Test, 170
Short Circuit Test Duration, 170
Signal Words, 1
Sink/Source Setting Error, 202
Sink/Source Switching, 33
Soft Stall, 78
Soft Stall Enable, 64
Soft Start, 64
Spare Parts Listing, 235
S-pattern 1, 155
S-pattern 2, 155
S-Pattern Lower Limit Adjustment, 156
S-Pattern Upper Limit Adjustment, 156
Special Control Parameters, 69
Special Parameters, 70
Speed at Drooping Gain 0%, 130
Speed at Drooping Gain 100%, 130
Speed Drop Detection Frequency Range, 172
Speed Limit (torque) Reference, 146
Speed Limit Torque Level, 146
Speed Limit Torque Range, 146
Speed Limit Torque Recovery, 146
Speed Loop Integral Gain, 138
Speed Loop Parameter Ratio, 138
Speed Loop Proportional Gain, 138
Speed Reach Frequency, 81
Speed Reach Frequency Range, 81
Speed Ref. Setpoint, 62
Speeds, 66
splash screen display, 34
ST, 28
ST Input Terminal Assignment, 85
ST Input Terminal Delay, 90
ST Signal Selection, 82
ST terminal, 29
ST1, 21, 22
Stall, 63
Stall Cooperation Gain at Field Weakening Zone, 152
Stall Prevention During Regeneration, 149
Standard Mode Settings, 59
Startup and Test, 37
Startup Frequency, 117
Startup Wizard, 44, 59
Startup Wizard Requirements, 53
Status LED, 39
Stop Key, 39
Stop Pattern, 181
SW1, 32
SW2, 32
Switching Frequency of Current/Voltage Control, 153
Switching Load Torque During Forward-Run, 69, 132
Switching Load Torque During Reverse-Run, 133
Synchronized Torque Bias Input, 144
System Grounding, 27