108
HX7+ ASD Installation and Operation Manual
RX Speed Reference #1
Program
Frequency Setting
Speed Reference Setpoints
RX
This parameter is used to set the gain and bias of the
RX
input terminal when
the
RX
terminal is used as the control input while operating in the
Speed
Control
mode or the
Torque Control
mode.
RX Input Speed Control Setup
Perform the following setup to allow the system to receive
Speed
control input
at the
RX
input terminal:
•
Program
Fundamentals
Standard Mode Selection
Frequency
Mode #1
RX
.
•
Program
Fundamentals
Standard Mode Selection
Command
Mode
Use Terminal Board
.
•
Set
RX Speed Reference #1
) — the input signal level that
represents
RX Speed Frequency #1
.
•
Set
RX Speed Frequency #1
•
Set
RX Speed Reference #2
) — the input signal level that
represents
RX Speed Frequency #2.
•
Set
RX Speed Frequency #2
•
Provide a
Run
command (
F
and/or
R
).
Once set, as the
RX
input changes, the output frequency of the ASD will vary
in accordance with the above settings.
This parameter sets
RX Speed Reference #1
and is the input signal level that is
associated with the setting of
RX Speed Frequency #1
while operating in the
Speed Control
mode.
RX Input Torque Control Setup
Perform the following setup to allow the system to receive
Torque
control input
at the
RX
input terminal:
•
Program
Fundamentals
Standard Mode Selection
Frequency
Mode #1
RX
.
•
Program
Fundamentals
Standard Mode Selection
Command
Mode
Use Terminal Board
.
•
Set
RX Speed Reference #1
) — the input signal level that
represents
RX Torque Reference Setpoint #1
.
•
Set
RX Torque Reference Setpoint #1
).
•
Set
RX Speed Reference #2
) — the input signal level that
represents
RX Torque Reference Setpoint #2.
•
Set
RX Torque Reference Setpoint #2
).
•
Provide a
Run
command (
F
and/or
R
).
Once set, as the
RX
input changes, the output torque of the ASD will vary in
accordance with the above settings.
This parameter sets
RX Speed Reference #1
and is the input signal level that is
associated with the setting of
RX Torque Reference Setpoint #1
while
operating in the
Torque Control
mode.
Direct Access Number — F216
Parameter Type —
Numerical
Factory Default —
00.0
Changeable During Run —
Yes
Minimum — -100.0
Maximum — 100.0
Units — %
Frequency Settings
Note:
The speed control response
may be further trimmed by
adjusting the Bias and
Gain settings.
Torque Settings
Summary of Contents for HX7+ ASD
