Mitsubishi Electric 3F-14C-WINE Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 646

background image

5-62

5-62

Function

Explanation

Position repair

Supports recovery from home position deviation

Password Setup

Registers, changes, or deletes the password to limit controller access
rights.

Option card

You can check information on option cards mounted in the robot controller.

Tool

Oscillograph

The various robot controller data are displayed in a graph.

DXF File Import

Imports DXF files for conversion into robot program / spline files.

User definition screen

It is possible to edit the user definition screen which can be operated by
the high-functionality T/B.

File Manager

You can copy, delete and rename the files in the robot controller.

2D Vision Calibration

Run the 2D vision calibration.

Force sensor
calibration

This Function calculates the weight and center of gravity position of robot
hand attached to the force sensor to be used for the gravity offset cancel in
Force sensor.

Force control log
viewer

This function can display force control log data graph in the PC and robot
controllers.

Tool automatic
calculation

The tool length is calculated automatically and the value of a tool
parameter is set up.

Simulation

This can be used in connection with a virtual robot.
*This can only be used in the standard edition.

Same functions as
online

The same functions can be used with a virtual robot controller as with an
online one.

Tact time calculation

The tact time for the robot program with the specified contents can be
calculated in the simulation.

MELFA-Works

You can be used the function of MELFA-Works (as 3D robot simulator).
*This can only be used with the Pro edition.

Backup, restore

You can back up the information in the robot controller and restore
backed-up information to the controller.

MELFA 3D-Vision

You can do a setup of MELFA-3D Vision.

I/O Simulator

Simulates the signal communication between robots.

Document out

You can output the each information in robot controller and offline setting
to the HTML document.

Robot firmware update

You can update the firmware of the robot controller.
Since this function is a function for maintenance, not open to the public.

«
...
60
61
62
63
64
...
»

Содержание 3F-14C-WINE







































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3F-14C-WINE

Бренд: Thames & Kosmos Страницы: 64

Бренд: Pro's Kit Страницы: 48

Бренд: ABB Страницы: 284

Бренд: ON Development IVS Страницы: 27

Бренд: MIP Страницы: 12

Бренд: Recon Scout Страницы: 10

Бренд: ReconRobotics Страницы: 36

Бренд: 4M Страницы: 2

Octopus Robotic Claw

Бренд: 4M Страницы: 2

Бренд: Tibhar Страницы: 14

Бренд: ABB Robotics Страницы: 24

JMHZ2-20D-X7510

Бренд: SMC Networks Страницы: 2

Бренд: Leju Robotics Страницы: 28

Omni Drive Module

Бренд: neobotix Страницы: 28

Бренд: neobotix Страницы: 36

Бренд: labrobotics Страницы: 30

Бренд: Variobot Страницы: 97

POLOLU STSPIN220

Бренд: Eckstein komponente Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды