Case 2050M Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 286

Case 2050M Скачать руководство пользователя страница 97

3 - CONTROLS AND INSTRUMENTS

Engine selections

Change the automatic fan control ON or OFF with this en-
gine setting. The fan configuration will change from auto-
matic to manual. At the automatic setting, both the speed
and direction (reverse) are controlled by the multi-function
display. The fan functions are determined by the hydraulic
oil temperature, engine coolant temperature, and charge
air. In the manual selection the fan speed is a set at the
maximum fan speed of 100%. The machine will default to
the automatic fan control setting.

RAIL12DOZ0213AA

13

RAIL12DOZ0649AA

14

Transmission selections

RevSpdDiff — Indicates speed differential between re-
verse and forward.
Shuttle — Adjusts ground drive ramps: smooth, moder-
ate, or aggressive.
Steer — Adjusts steering curves: smooth, moderate, or
aggressive.
Pedal — Adjusts transmission command (default).
Change from transmission pedal to deceleration pedal.
AutoPrkBrk — When the “AutoPrkBrk” function is set to
“ON”, the unit is in neutral, and the UCM senses move-
ment from the drive motor speed sensors for

30 s

, the

park brake will engage.
1. ON (default)
2. OFF
Max Speed — Sets speed in increments: 15, 13, 11, 9.

RAIL14DOZ0583AA

15

3-49

«
...
95
96
97
98
99
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов