Case 2050M Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 286

Case 2050M Скачать руководство пользователя страница 52

3 - CONTROLS AND INSTRUMENTS

OPERATOR'S SEAT

Operator's seat

WARNING

Loss of control hazard!
DO NOT make seat adjustments while the machine is in motion. All seat adjustment should be made
with the machine stationary and the parking brake applied.
Failure to comply could result in death or serious injury.

W0293A

Cab machines are equipped with cloth air suspension seats. Adjust the seat so that you can fully depress the de-
celeration or transmission pedal when your back is against the seat backrest. Adjustments for all styles of seats are
similar.

Lumbar adjustment

Locate the lumbar adjustment knob on the back of the op-
erator’s seat. Turn the knob clockwise to increase the
lumbar support. Turn the knob counterclockwise to de-
crease the lumbar support.

RAIL12DOZ0548AA

1

Backrest adjustment

The backrest adjustment is located on the left-hand side
of the operator’s seat. To adjust the backrest lift up on the
handle, move the backrest to the desired position, and
release the handle. Tilt the seat back completely forward
to access the cab air filter and operator’s manual storage
pocket.

RAIL12DOZ0650AA

2

3-4

«
...
50
51
52
53
54
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов