Case 2050M Скачать руководство пользователя страница 221

Страница: 221 / 286

7 - MAINTENANCE

2. Remove the bolts and remove the panel.

RAIL12DOZ0410AA

3. Pull the fuel tank drain hose forward, and remove the

fitting.

4. Open the fuel shut off valve located on the fuel tank,

and drain the water and sediment into a suitable con-
tainer.

RAIL12DOZ0412AA

NOTE:

The fuel tank shut off valve is accessible through the right rear access panel or by removing the cab floor

access panel and tilting back the seat.

5. Turn the shut off valve to the closed position after only

clean fuel is discharged. Replace the fitting on the
hose.

6. Replace the hoses within the panel and wire tie, if nec-

essary.

7. Check for leaks.

8. Replace the bolts and the cover panel.

7-65

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 221 / 286

Результаты поиска

Содержание 2050M

Отзывы: