Case 2050M Скачать руководство пользователя страница 245 | Manualshive

Страница: 245 / 286

Case 2050M Скачать руководство пользователя страница 245

7 - MAINTENANCE

Roll Over Protective Structure (ROPS)

WARNING

Roll-over hazard!
After an accident, fire, tip over, or roll over, a qualified technician MUST replace the Roll-Over Protec-
tive Structure (ROPS) before returning the machine to the field or job site operation.
Failure to comply could result in death or serious injury.

W0134A

WARNING

Misuse hazard!
Your machine is equipped with an operator protective structure. DO NOT weld, drill holes, attempt
to straighten, or repair the protective structure. Modification in any way can reduce the structural
integrity of the structure.
Failure to comply could result in death or serious injury.

W0001B

Your machine is equipped with an operator protective
structure, such as:

Roll Over Protective Structure

(ROPS) or Falling Object Protective Structure (FOPS).
A ROPS may be a cab frame or a two-posted or
four-posted structure used for the protection of the
operator to minimize the possibility of serious injury.
The mounting structure and fasteners forming the
mounting connection with the machine are part of the
ROPS. The Protective Structure is a special safety
component of your machine.

DO NOT attach any

device to the protective structure for pulling purposes.
DO NOT drill holes into the protective structure. The
protective structure and interconnecting components
are a certified system. Any damage, fire, corrosion or
modification will weaken the structure and reduce your
protection. If this occurs, the protective structure MUST
be replaced so that it will provide the same protection
as a new protective structure. Contact your authorized
dealer for protective structure inspection and replace-
ment. The protective structure MUST be replaced. The
mounting or suspension for the protective structure,
operator seat and suspension, seat belts and mounting
components and wiring within the operator’s protective
system MUST be carefully inspected for damage. All
damaged parts MUST be replaced.

RAPH12DOZ0045AA

1

ROPS certification plate

The machine has a ROPS plate showing the certifica-
tion of the ROPS, gross weight, approval, regulation,
and model number of the machine.

Check and inspect the ROPS structure and the seat
restraint system as required.

The ROPS certification plate is located inside the left
rear access compartment.

7-89

«
...
243
244
245
246
247
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов