Case 2050M Скачать руководство пользователя страница 144 | Manualshive

Страница: 144 / 286

Case 2050M Скачать руководство пользователя страница 144

6 - WORKING OPERATIONS

Bulldozer blade — Push beam centering

1. Set the bulldozer blade on a level surface. Make sure

the blade is even when it rests on the ground.

2. Raise the blade slightly off the ground.

RAIL14DOZ0525AA

9

3. Remove the bolts

(A)

,

(B)

from both ends of the left-

hand

(C)

and right-hand

(D)

turnbuckles to allow move-

ment of the turnbuckle body

(E)

.

RAPH15DOZ0008BA

10

4. Extend the left-hand turnbuckle

(C)

(rotate 1/2 turn)

counter-clockwise when positioned behind the blade
as shown. Extend the right-hand turnbuckle (rotate
1/2 turn) counter-clockwise when positioned behind the
blade. Continue to alternately turn each turnbuckle un-
til both turnbuckles are tight.

RAIL14DOZ0529AA

11

6-8

«
...
142
143
144
145
146
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов