manualshive.com logo in svg

Case 2050M, Руководство оператора, Страница: 58 / 286

Поделиться
Скачать
Case 2050M Скачать руководство пользователя страница 58

3 - CONTROLS AND INSTRUMENTS

Front console

Instrument panel

RAPH12DOZ0136FA

1

NOTICE:

The warning lights will illuminate momentarily when the ignition switch is turned on. Check and/or replace

the fuse if the lamps do not illuminate.

1. Work light lamp

The work light lamp will illuminate when the machine light switch is turned on.

2. Service

The service lamp indicates service is required. Contact your authorized dealer or read your service
and/or operator’s manual for correct service methods, intervals, and fluid/consumable requirements.

3. Hydrostatic drive filter

The hydrostatic drive filter warning lamp shows the condition of the hydrostatic drive filter. Stop the
engine, and replace the filter if the warning lamp illuminates during normal operation (hydraulic oil at
operating temperature and engine at full throttle).

3-10

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов