Case 2050M Скачать руководство пользователя страница 252 | Manualshive

Страница: 252 / 286

Case 2050M Скачать руководство пользователя страница 252

7 - MAINTENANCE

Selective Catalytic Reduction System (SCR) tank filter

Clean the SCR tank filter as required.

Prior operation:

Keep all unauthorized personnel clear of the area. Park the machine on level ground, in neutral with the parking
brake applied, and the attachment lowered to the ground. Make sure that all residual pressure is relieved from circuits
before beginning maintenance.

1. The DEF tank mesh filter is located within the neck

of the DEF fill tube. Open the DEF fill compartment.
Clean the area to be serviced in order to prevent DEF
tank contamination.

RAIL12DOZ0362AA

1

2. Remove the DEF cap. Remove the hex screws with an

Allen wrench.

RAIL12DOZ0905BA

2

3. Remove the tank filter assembly and the O-ring from

the DEF tank neck. Rinse the tank filter with water

4. Reinstall the O-ring on the DEF tank neck with the ra-

dius surface facing up.

5. Reinstall the tank filter assembly securing it with the

hex screws.

6. If the tank filter has been damaged, replace the tank

filter. To replace, separate the tank filter and fit a new
tank filter to the assembly.

7. Insert assembly into orifice. Attach the assembly using

with the hex screws.

RAIL12DOZ0387AA

3

7-96

«
...
250
251
252
253
254
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов