Case 2050M Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 286

Case 2050M Скачать руководство пользователя страница 45

2 - SAFETY INFORMATION

WARNING — Belt Entanglement hazard

RAIL13DOX1617AA

30

This WARNING safety sign is located on both sides
of the machine just ahead of the engine front access
doors.
Keep clear or stop the engine before servicing. Failure
to comply with this warning could result in death or
serious injury.
ISO safety sign number: 81871830

81871830

31

WARNING — Pinch hazard

RAIL13DOX1617AA

32

This WARNING safety sign is located on both sides of
the machine just ahead of the engine front access lower
doors.
WARNING — Pinch hazard keep clear. Failure to
comply could result in death or serious injury.
English safety sign number: 84394350
French safety sign number: 87741372
Spanish safety sign number: 87741372

84394350

33

2-23

«
...
43
44
45
46
47
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов