Case 2050M Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 286

Case 2050M Скачать руководство пользователя страница 53

3 - CONTROLS AND INSTRUMENTS

Slide adjustment lever

Pull the slide adjustment lever up and adjust the seat for-
ward or backward as required. Release the lever to lock
the seat in position. Always make adjustments from the
front center of the adjustment bar.

RAPH12DOZ0075AA

3

Seat height adjustment

To raise the seat, push the knob and remove your weight
off the seat. Allow the air to build to the desired height.
Release the knob at the desired height.

To lower the seat, pull the knob out to release air. Release
the knob at the desired height.

NOTE:

Over time, there will be some air loss. Readjust

the seat at the beginning of each work day.

RAIL12DOZ0651AA

4

Armrest height

Depress the knob on the armrest adjustment lever, and
push the lever forward. Both the left and right arm rest
height can be adjusted. Return the lever to the back po-
sition to lock the desired height in place.

RAIL12DOZ0166AA

5

3-5

«
...
51
52
53
54
55
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов