Case 2050M Скачать руководство пользователя страница 222 | Manualshive

Страница: 222 / 286

Case 2050M Скачать руководство пользователя страница 222

7 - MAINTENANCE

Fuel tank cap

WARNING

Hot liquid under pressure!
Fuel in the high pressure fuel line is still under pressure immediately after you shut down the engine.
Before performing any maintenance or inspection, wait for 2 minutes after engine shutdown to allow
the pressure to drop.
Failure to comply could result in death or serious injury.

W0249A

WARNING

Fuel vapors are explosive and flammable.
Do not smoke while handling fuel. Keep fuel away from flames or sparks. Shut off engine and remove
key before servicing. Always work in a well-ventilated area. Clean up spilled fuel immediately.
Failure to comply could result in death or serious injury.

W0904A

Clean the fuel cap breather when the hour meter registers 1000 hours and every 1000 hours thereafter. Clean more
frequently, if conditions so require. The cap allows air to be drawn in to create pressure in the fuel tank. Air displaces
the used fuel.

Prior operation:

Keep all unauthorized personnel clear of the area. Park the machine on level ground, in neutral with the parking
brake applied, and the attachment lowered to the ground. Make sure that all residual pressure is relieved from circuits
before beginning maintenance.

1. Remove the fuel cap slowly. The fuel cap is located at

the rear of the machine.

RAPH12DOZ127AA

1

2. Clean the cap, and dry with compressed air.

3. Reinstall cap, tightening firmly in place.

RAIL12DOZ0365AA

2

NOTICE:

Always replace fuel cap with an genuine authorized fuel cap if replacement is necessary. An approved,

factory fuel cap replacement is necessary for correct fuel tank pressure.

7-66

«
...
220
221
222
223
224
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов