Case 2050M Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 286

Case 2050M Скачать руководство пользователя страница 78

3 - CONTROLS AND INSTRUMENTS

LEFT-HAND SIDE CONTROLS

Control levers

WARNING

Hazard to bystanders!
Always sound the horn before starting the machine. Make sure the work area is clear of other persons,
domestic animals, tools, etc. before you operate the machine. Never allow anyone in the work area
during machine operation.
Failure to comply could result in death or serious injury.

W0304A

Horn button

The direction control lever allows for directional move-
ment of the machine. The horn button is also located on
the direction control lever. Always sound the horn before
starting the machine.

RAIL12DOZ0181AA

1

Direction control lever

The direction control lever

(1)

allows forward, reverse,

neutral direction, turning and counter rotation.
The lever has detent positions for neutral, forward, and
reverse. The lever remains in the forward or reverse po-
sition until it is moved by the operator. Turning is also con-
trolled by the direction control lever. The direction control
lever has a feel point for left and right counter rotation.
Use the machine in a clear, unobstructed area until you
become familiar with the controls. See page

4-10

for ad-

ditional information on operating the machine.

RAPH12DOZ0080AA

2

3-30

«
...
76
77
78
79
80
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов