Case 2050M Скачать руководство пользователя страница 126

Страница: 126 / 286

5 - TRANSPORT OPERATIONS

7. Press the enter switch to continue to the next screen.

NOTICE:

Tow the machine the shortest possible distance.

RAIL12DOZ0827AA

8. The tow mode will be enabled. Wait for the next screen

prompt before you tow the machine.

NOTICE:

Before you proceed to step 9 in this instruc-

tion, you must follow the procedures on page

5-5

–

before you tow the machine.

RAIL12DOZ0828AA

9. When the tow mode is enabled, tow the machine at

a slow rate of speed following all safe towing proce-
dures. Change the tow mode screen back to the “Dis-
abled” mode when tow is complete.

RAIL12DOZ0829AA

NOTICE:

Higher towing speeds and longer towing distances will result in high heat generation and insufficient lubri-

cation. This will cause machine damage.

5-4

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 126 / 286

Результаты поиска

Содержание 2050M

Отзывы: