Case 2050M Скачать руководство пользователя страница 216

Страница: 216 / 286

7 - MAINTENANCE

11. Fill the engine with the proper amount of oil through

the fill port

(4)

12. Start the engine and run at idle speed. Check the

engine oil filter and remote drain for leaks.

13. After

2 min

stop the engine.

14. Wait for the engine oil to drain down for an accurate

reading on the dipstick

(1)

RAIL13DOZ1693AA

15. Check the dipstick

(1)

and add additional oil, if neces-

sary.

16. Check for leaks around the filter and drain.

17. Secure the lower engine access plate.

RAIL13DOZ1694AA

NOTE:

The oil flow rate can be improved if the oil is slightly warm and the oil fill cap or dipstick is removed from the

engine while draining.

7-60

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 216 / 286

Результаты поиска

Содержание 2050M

Отзывы: