manualshive.com logo in svg

Case 2050M, Руководство оператора, Страница: 65 / 286

Поделиться
Скачать
Case 2050M Скачать руководство пользователя страница 65

3 - CONTROLS AND INSTRUMENTS

Hydraulic oil temperature gauge

The hydraulic oil temperature gauge

(2)

indicates the oil temperature of the hydraulic
system.

The normal operating temperature is in the green zone.
When the hydraulic oil temperature increases, the gauge
will move into the yellow zone, the warning alarm sounds,
and the caution master indicator turns yellow. If the tem-
perature continues to increase the gauge moves into the
red zone, the audible warning alarm will sound continu-
ously, and the stop master indicator turns red. Do not
operate the machine when the temperature is in the red
zone.

RAPH12DOZ0138AA

5

Hydraulic oil temperature gauge

Gauge indication

Condition

Master

indicator

Gauge status

Alarm status

37 - 90 °C

(

99 - 194 °F

) Oil temperature is normal

90 - 100 °C

(

194 -

212 °F

)

(See the notice below.)

Oil temperature is high

Caution (yellow) Solid

1 Second

100 °C

(

212 °F

) and

above

Oil temperature is very high

Stop (red)

Solid

Continuous

NOTICE:

To prevent damage to the hydraulic system, stop the machine, shift to neutral, and run the engine at partial

throttle, approximately

1700 RPM

until the system cools. If the hydraulic oil temperature does not return to normal

operating temperature, check the hydraulic oil level. Correct the problem before continuing to operate the machine.

3-17

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов