Case 2050M Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 286

Case 2050M Скачать руководство пользователя страница 43

2 - SAFETY INFORMATION

DANGER — Unexpected movement hazard

RAIL13DOZ1705AA

22

This DANGER safety sign is located in the right front
engine compartment.
DANGER — Starting in gear can cause death.
Start engine only from the operator’s seat with the
transmission control(s) in neutral. Failure to comply with
this warning will result in death or serious injury.
English safety sign number: 321–7040
French safety sign number: 87715063
Spanish safety sign number: 87715063

3217040

23

DANGER — Explosion hazard/Run over hazard

RAPH12DOZ0043AA

24

This DANGER safety sign is located in the left rear
access compartment.
DANGER — Explosion hazard/Run over hazard. Read
procedure in operator’s manual before jump start or
service. Failure to comply with this warning will result
in death or serious injury.
English safety sign number: 383973A1
French safety sign number: 87706390
Spanish safety sign number: 87706390

383973A1

25

2-21

«
...
41
42
43
44
45
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов