Case 2050M Скачать руководство пользователя страница 204 | Manualshive

Страница: 204 / 286

Case 2050M Скачать руководство пользователя страница 204

7 - MAINTENANCE

Replace hydraulic oil filters (Initial)

WARNING

Pressurized hydraulic fluid can penetrate the skin and cause severe injuries.
Hydraulic fluid is under extreme pressure. Rest the bucket or attachment on the ground. Shut the
engine off, turn the key on, and move the hydraulic control lever through all movements several times
to relieve residual pressure in the system.
Failure to comply could result in death or serious injury.

W0161A

WARNING

Pressurized fluid can penetrate the skin and cause severe injuries.
Keep hands and body away from any pressurized leak. DO NOT use your hand to check for leaks. Use
a piece of cardboard or paper. If fluid penetrates the skin, seek medical attention immediately.
Failure to comply could result in death or serious injury.

W0158A

Replace the hydraulic oil filter when the hour meter registers 100 hours for a new machine during the initial run-in
period. The filter should be changed every 2000 hours thereafter or more frequently when operating conditions are
severe.

Prior operation:

Keep all unauthorized personnel clear of the area. Park the machine on level ground, in neutral with the parking
brake applied, and the attachment lowered to the ground. Make sure that all residual pressure is relieved from circuits
before beginning maintenance. Install the transport service link to prevent unexpected articulation.

1. The hydraulic oil filler cap is located on the rear of the

machine.

2. Stop the engine. Put a Do Not Operate tag on the key

switch.

3. Make sure the accumulators on the machine are com-

pletely discharged.

4. Clean the area around the hydraulic oil filler cap, and

slowly loosen the cap to release any remaining pres-
sure.

RAPH12DOZ128AA

1

5. Remove and replace the hydraulic oil filter

(1)

. Turn the

filter counter clockwise to remove.

6. Clean the contact surface on the filter head. Make sure

that all dirt and gasket material has been removed.

7. Apply a thin coat of clean oil to the hydraulic oil gasket

and threads.

8. Install and tighten the new filter cartridge firmly to the

filter head by hand. Do not use a filter wrench to tighten
the filter.

RAIL13DOZ1699AA

2

7-48

«
...
202
203
204
205
206
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов