Case 2050M Скачать руководство пользователя страница 236

Страница: 236 / 286

7 - MAINTENANCE

5. The hydraulic reservoir drain is located in the upper

right hand side of the access compartment.

RAIL12DOZ0378AA

NOTE:

A drain hose is included on machines equippedwith the environmental drain option.

6. Open the hydraulic reservoir drain, and drain the oil into

a suitable container.

7. After oil has completely drained, close the drain, and

replace the access cover.

8. Remove and replace the hydraulic oil filter

(1)

. Turn the

filter counterclockwise to remove.

9. Clean the contact surface on the filter head. Make sure

that all dirt and gasket material has been removed.

10. Apply a thin coat of clean oil to the hydraulic oil gasket

and threads.

11. Install and tighten the filter firmly to the filter head by

hand. Do not use a filter wrench to tighten the filter.

RAIL13DOZ1699AA

12. Remove the bolts and the cover from the right rear

access panel.

RAIL12DOZ0177AA

7-80

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 236 / 286

Результаты поиска

Содержание 2050M

Отзывы: