Case 2050M Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 286

Case 2050M Скачать руководство пользователя страница 103

4 - OPERATING INSTRUCTIONS

4 - OPERATING INSTRUCTIONS

###_4_###

COMMISSIONING THE UNIT

Before starting the engine

WARNING

IMPROPER OPERATION OF THIS MACHINE CAN CAUSE DEATH OR SERIOUS INJURY.
MAKE SURE THAT EVERY OPERATOR:
-is instructed in the safe and proper use of this machine.
-reads and understands the operator's manual for this machine.
-reads and understands ALL safety signs on the machine.
Failure to comply could result in death or serious injury.

W0188A

WARNING

Avoid injury!
Do not operate the machine while under the influence of alcohol or drugs.
Failure to comply could result in death or serious injury.

W0160A

Before starting the engine

1. Perform a daily walk around and visual inspection of the machine.

2. Check for loose connections, faulty hoses, oil leaks, debris or trash buildup, loose bolts, damaged, or missing

parts that could affect the normal and safe operation of the machine.

3. Make any necessary corrections before operating the machine.

4. Complete recommended daily maintenance.

5. Check that the machine fuel tank is filled with clean fuel that matches the specifications given in this manual.

6. Check and make certain the DEF tank is properly filled. Low volume in the tank can cause loss of power and

torque. The tank will need to be filled after approximately two fuel fills. Do not allow the DEF tank to drop below

10 %

volume for the best engine performance.

4-1

«
...
101
102
103
104
105
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов