Case 2050M Скачать руководство пользователя страница 18

Страница: 18 / 286

1 - GENERAL INFORMATION

1. Perform a complete after-run procedure.

2. Drain the

DEF/A

LUE

tank.

3. Flush the tank with deionized water.

4. Drain the deionized water

NOTICE:

Do not disconnect any electrical connections from the

DEF/A

LUE

system.

Machine start-up after extended shutdown:

1. Fill the

DEF/A

LUE

tank.

2. Replace the main filter in the supply module.

3. Start the machine.

Thawing

• Your CASE CONSTRUCTION machine is equipped with an internal tank heater to thaw frozen

DEF/A

LUE

Your machine will still function until the

DEF/A

LUE

begins to flow. The SCR system will then function normally.

NOTE:

You may notice a slight reduction in engine torque in high demand situations until the

DEF/A

LUE

is fully

thawed.

• Do not heat

DEF/A

LUE

for long periods of time at temperatures above

30 °C

(

86 °F

). This causes the solution

to decompose, which very slowly decreases the expected shelf life.

NOTICE:

Do not use an anti-gelling or freeze point improver in your

DEF/A

LUE

. The

32.5 %

solution is specifically

designed to provide the optimum NO

reduction properties. Any further blending or adjusting of the

DEF/A

LUE

mixture will lessen its ability to perform correctly and may cause damage to the SCR components.

Handling and supply of additives, if any.

• Personal Protective Equipment (PPE) is not required under normal conditions. If splashing is likely, wear eye pro-

tection. For prolonged or repeated contact, impervious gloves are recommended. Follow the precautions listed in
the SAFETY INFORMATION chapter when handling any service fluid.

• No additives are required.

NOTICE:

Contaminated

DEF/A

LUE

can affect the performance of your machine. Follow all instructions in this

manual when handling

DEF/A

LUE

Shelf life

Constant ambient storage temperature

Minimum shelf life

Less than or equal to

10 °C

(

50 °F

)

36 months

Less than or equal to

25 °C

(

77 °F

) ¹

18 months

Less than or equal to

30 °C

(

86 °F

)

12 months

Less than or equal to

35 °C

(

95 °F

)

6 months

Greater than

35 °C

(

95 °F

)

-²

¹ To prevent decomposition of

DEF/A

LUE

, prolonged transportation or storage above

25 °C

(

77 °F

) should

be avoided.
² Significant loss of shelf life: check every batch before use. See your CASE CONSTRUCTION dealer for more
information on testing.

NOTE:

The main factors taken into account to define the shelf life in the table above are the ambient storage tem-

perature and the initial alkalinity of

DEF/A

LUE

. The difference in evaporation between vented and non-vented

storage containers is an additional factor.

NOTE:

The information in this table is for reference only and has been provided by the International Organization for

Standardization, Document number

ISO 22241-3

Diesel engines - NO

reduction agent AUS 32 - Part 3: Handling,

transportation and storage.

NOTE: DEF/A

LUE

that remains in the tank of the machine after the season does not require any special precau-

tions unless storage exceeds the shelf life table above.

Disposal

• Dispose of

DEF/A

LUE

and any filter accumulations in accordance with all applicable Federal, State, and local

laws governing waste disposal.

1-12

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 18 / 286

Результаты поиска

Содержание 2050M

Отзывы: