Case 2050M Скачать руководство пользователя страница 250 | Manualshive

Страница: 250 / 286

Case 2050M Скачать руководство пользователя страница 250

7 - MAINTENANCE

Cab air filter - Recirculation filter

WARNING

Eye injury hazard!
Wear full coverage safety glasses with side panels when using compressed air. Limit air pressure to
200 kPa (29 psi).
Failure to comply could result in death or serious injury.

W0162A

The cab recirculation air filter is located behind the operator’s seat. Replace the cab air filters when required. The
cab air filter is located behind the operator compartment near the exhaust fan.

Prior operation:

Keep all unauthorized personnel clear of the area. Park the machine on level ground, in neutral with the parking
brake applied, and the attachment lowered to the ground. Make sure that all residual pressure is relieved from circuits
before beginning maintenance.

Recirculation filter

1. Remove the retaining screw that holds the recirculation

filter cover in place, and remove the recirculation filter.

2. Wipe the housing clean.

RAPH12DOZ0074AA

1

3. Replace the recirculation filter with a new one.

4. Reinstall the new recirculation filter, and secure the ac-

cess filter cover.

RAIL12DOZ0164AA

2

7-94

«
...
248
249
250
251
252
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов