Case 2050M Скачать руководство пользователя страница 90

Страница: 90 / 286

3 - CONTROLS AND INSTRUMENTS

EXTERIOR CONTROLS

Master disconnect switch

The master electrical disconnect switch is located on the
left side of the machine. The switch has two positions:
ON and OFF.

Master electrical switch ON

The master disconnect switch in the ON
position energizes the entire electrical
system.

Master electrical switch OFF

All machine power is interrupted in the OFF
position.

NOTICE:

DO NOT use the master electrical disconnect

switch to stop the engine.

NOTE:

After engine shutdown, the SCR system will per-

form a purge cycle which permits the supply module to
continue to run. Do not shut off the master disconnect for
70 seconds after key off.

RAPH12DOZ0044AA

3-42

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 90 / 286

Результаты поиска

Содержание 2050M

Отзывы: