Case 2050M Скачать руководство пользователя страница 10

Страница: 10 / 286

1 - GENERAL INFORMATION

Electro-Magnetic Compatibility (EMC)

Interference may arise as a result of add

‐

on equipment that may not necessarily meet the required standards. As

such interference can result in serious malfunction of the unit and/or create unsafe situations, you must observe
the following:

• The maximum power of emission equipment (radio, telephones, etc.) must not exceed the limits imposed by the

national authorities of the country where you use the machine

• The electro

‐

magnetic field generated by the add

‐

on system should not exceed

24 V/m

at any time and at any lo-

cation in the proximity of electronic components

• The add

‐

on equipment must not interfere with the functioning of the on board electronics

Failure to comply with these rules will render the CASE CONSTRUCTION warranty null and void.

1-4

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 10 / 286

Результаты поиска

Содержание 2050M

Отзывы: