Case 2050M Скачать руководство пользователя страница 246 | Manualshive

Страница: 246 / 286

Case 2050M Скачать руководство пользователя страница 246

7 - MAINTENANCE

Seat belt

WARNING

Equipment failure could cause accident or injury!
Always fasten the seat belt securely before you operate the machine. Inspect seat belt parts for wear
and damage. Replace any and all worn or damaged parts of the seat belt prior to operation.
Failure to comply could result in death or serious injury.

W0046C

Before you operate this machine, always make sure the
ROPS and operator’s seat belt

(1)

is correctly installed.

The seat belt is an important part of the ROPS. You
must wear the seat belt at all times when you operate
the machine.

1. Make sure all that seat belt hardware is secure and

torqued.

2. Visually inspect the seat belt. If the seat belt is torn,

frayed, or the mechanism is damaged, replace the seat
belt.

3. Keep the seat belts clean. Wash the seat belts only in

soap and water. Do not use bleach or dye on the seat
belts. This will weaken the seat belt composition.

4. Torque seat belt hardware and seat mounting hardware

to:

73 - 87 N·m

(

53.8 - 64.2 lb ft

).

RAPH12DOZ0389AA

2

Seat and mounting hardware

Make sure that all hardware that secures the seat

(2)

to

the cab is properly torqued (two each side). The seat
can be cleaned with a suitable upholstery cleaner.
Torque to:

54 N·m

(

39.8 lb ft

).

RAPH12DOZ0388AA

3

7-90

«
...
244
245
246
247
248
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов