Case 2050M Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 286

Case 2050M Скачать руководство пользователя страница 115

4 - OPERATING INSTRUCTIONS

Direction control lever

WARNING

IMPROPER OPERATION OF THIS MACHINE CAN CAUSE DEATH OR SERIOUS INJURY.
MAKE SURE THAT EVERY OPERATOR:
-learns and practices the safe use of machine controls in a safe, clear area before operating the ma-
chine on a job site.
-clears the work area of all bystanders.
-observes pertinent laws and regulations.
-follows the instructions in this operator's manual.
Failure to comply could result in death or serious injury.

W0189A

Control the drive and steering with the direction control
lever. The direction control lever sends an electronic sig-
nal to the controller.

The directional control lever has a detent in the neutral,
forward, and reverse positions. The lever will stay in the
forward or reverse position until you remove it from either
detent. At start up, the crawler must be in the neutral po-
sition for several seconds before the machine will move.
The directional control lever position will be displayed on
the instrument gauge.

The sensitivity or feel of the direction control lever can be
adjusted to moderate, smooth, or aggressive.

RAPH12DOZ0080AA

1

Direction control lever

RAPH12DOZ0149AA

2

Move the direction control lever to the position desired
(forward-neutral-reverse) and verify the selection on the
multi-function display (neutral shown).

NOTE:

The crawler will not move unless the engine speed

is above approximately

1200 RPM

.

Turn the crawler by moving the direction control lever in
the direction desired. Turning is accomplished through
forward or reverse only. Moving the control lever left or
right without being in forward or reverse will not move the
crawler.

RAIL12DOZ0224AA

3

4-13

«
...
113
114
115
116
117
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов