Case 2050M Скачать руководство пользователя страница 215

Страница: 215 / 286

7 - MAINTENANCE

5. Remove the engine oil drain plug

(2)

RAPH12DOZ0096AA

6. Locate the oil filter

(3)

in the right front engine compart-

ment. Clean the area around the filter of dirt and debris.

RAIL12DOZ0192AA

Replace oil filter

7. Turn the oil filter

(3)

housing counterclockwise to re-

move. Remove and discard the filter following local en-
vironmental and waste regulations.

8. Apply a thin layer of clean oil to the new filter gasket.

9. Turn the new oil filter onto the base until the gasket

makes contact with the base, and then turn by hand an
additional 3/4 turn. Never use a filter wrench to install
a new filter.

RAIL12DOZ0192AA

10. Close the oil drain.

7-59

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 215 / 286

Результаты поиска

Содержание 2050M

Отзывы: