Case 2050M Скачать руководство пользователя страница 135

Страница: 135 / 286

5 - TRANSPORT OPERATIONS

Transport dimensions

Transport length and width with blade fully angled at 25 °

RAIL14DOZ0569FA

LT model

Blade width

Transport width

Transport Length without drawbar

LT/XLT PAT blade

3287 mm

(

129.4 in

)

6021 mm

(

237.0 in

)

LT/XLT HS blade

3334 mm

(

131.3 in

)

5220 mm

(

205.5 in

)

LT/XLT HSU blade

3423 mm

(

134.8 in

)

5410 mm

(

213.0 in

)

XLT model

Blade width

Transport width

Transport Length without drawbar

LT/XLT PAT blade

3287 mm

(

129.4 in

)

6021 mm

(

237.0 in

)

LT/XLT HS blade

3334 mm

(

131.3 in

)

5220 mm

(

205.5 in

)

LT/XLT HSU blade

3423 mm

(

134.8 in

)

5410 mm

(

213.0 in

)

WT / LGP model

Blade width

Transport width

Transport length without drawbar

WT/LGP PAT blade

3632 mm

(

143 in

)

6522.7 mm

(

256.8 in

)

WT/LGP HS blade

3900 mm

(

153.5 in

)

5730 mm

(

225.6 in

)

WT/LGP PAT folding blade

3023 mm

(

119.0 in

)

3690 mm

(

145.3 in

)

6533.0 mm

(

257.2 in

)

Angled blade

NOTE:

Add

262 mm

(

10.3 in

) for drawbar. Add

1227 mm

(

48.3 in

) for the ripper.

NOTE:

The folding blade is straight when in transport and both ends are folded. The dimension shown is only the

blade width.

5-13

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 135 / 286

Результаты поиска

Содержание 2050M

Отзывы: