Case 2050M Скачать руководство пользователя страница 270 | Manualshive

Страница: 270 / 286

Case 2050M Скачать руководство пользователя страница 270

7 - MAINTENANCE

Removal from storage

Starting up after storage

WARNING

Inhalation hazard! Risk to operators and bystanders.
Avoid running the engine in confined areas. Make sure there is adequate ventilation at all times.
Failure to comply could result in death or serious injury.

W0156A

1. Close the drain valves, and fill the cooling system.

2. If the DEF tank was drained for long term storage (90

days or more), refill the tank with fresh fluid.

3. Drain the fuel reservoir and top up with suitable fuel.

4. Drain the engine sump, fill with clean engine oil, and

check the oil level.

5. Replace the filtering element of the fuel filters.

6. Install the batteries.

7. Grease the machine thoroughly.

8. Check the condition of the engine accessory drive belt,

and replace the belt, if necessary.

9. Check the condition of the air conditioning drive belt

and replace belt, if necessary.

10. Check the hydraulic fluid level, and add more fluid, if

necessary.

11. Clean the cylinder rods.

12. Unplug the air filter inlet and the exhaust pipe.

13. Remove the DO NOT OPERATE tag, and start the

engine following the starting up procedure. Keep non-
authorized personnel clear of the machine.

14. Keep a careful watch on all systems display panel

lamps and indicators.

7-114

«
...
268
269
270
271
272
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов