Case 2050M Скачать руководство пользователя страница 276

Страница: 276 / 286

8 - SPECIFICATIONS

Machine specifications and dimensions

RAIL14DOZ0570FA

Height and ground clearance dimensions

PAT models

BD models

XLT / WT

WT / LGP

A - Top of exhaust stack

2876.6 mm

(

113.3 in

)

2876.6 mm

(

113.3 in

)

2876.6 mm

(

113.3 in

)

2876.6 mm

(

113.3 in

)

B - Blade height

1369 mm

(

53.9 in

)

1369 mm

(

53.9 in

)

1108 mm

(

43.6 in

)

1108 mm

(

43.6 in

)

C1- Ground clearance at belly pans
(lowest)

325 mm

(

12.8 in

)

325 mm

(

12.8 in

)

325 mm

(

12.8 in

)

325 mm

(

12.8 in

)

C2 Ground clearance at drawbar

525.2 mm

(

20.7 in

)

525.2 mm

(

20.7 in

)

525.2 mm

(

20.7 in

)

525.2 mm

(

20.7 in

)

C3 - Centerline of drawbar opening

601.1 mm

(

23.7 in

)

601.1 mm

(

23.7 in

)

601.1 mm

(

23.7 in

)

601.1 mm

(

23.7 in

)

D - Shank height (transport position)

(**)

556.6 mm

(

21.9 in

)

556.6 mm

(

21.9 in

)

556.6 mm

(

21.9 in

)

556.6 mm

(

21.9 in

)

E - Top of seat headrest

2553.7 mm

(

100.5 in

)

2553.7 mm

(

100.5 in

)

2553.7 mm

(

100.5 in

)

2553.7 mm

(

100.5 in

)

F1 - Height of cab with air conditioner

3103.4 mm

(

122.2 in

)

3103.4 mm

(

122.2 in

)

3103.4 mm

(

122.2 in

)

3103.4 mm

(

122.2 in

)

NOTE: (1)

Ground clearance and overall height dimensions are with the grouser fully penetrated. Add

55.5 mm

(

2.2 in

) if the machine is on a solid surface.

NOTE: (**)

Ripper transport with shank in the mid-range position.

8-6

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 276 / 286

Результаты поиска

Содержание 2050M

Отзывы: