Case 2050M Скачать руководство пользователя страница 145

Страница: 145 / 286

6 - WORKING OPERATIONS

5. Measure from the body of the vertical lift cylinder to the

side of the frame at the same point

(A)

on both sides.

6. Adjust the turnbuckle, on the side of the smallest mea-

surement, in (retract) by 1/2 turn. Then adjust the op-
posite side out (extend) by 1/2 turn.

7. Measure again as noted in step

and continue until the

smallest measurement is on the opposite side.

8. If the difference between the left-hand and right-hand

measurements is now greater than it was before the
last adjustment, reverse the last adjustment.

NOTE:

By reversing the last adjustment, it will make the

difference between the sides as small as possible.

RAIL15DOZ0035BA

9. Lower the blade to the ground and rotate the turnbuck-

les two full turns in, then reinstall the turnbuckle bolts
to hold the turnbuckles in position.

6-9

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 145 / 286

Результаты поиска

Содержание 2050M

Отзывы: