Case 2050M Скачать руководство пользователя страница 189 | Manualshive

Страница: 189 / 286

Case 2050M Скачать руководство пользователя страница 189

7 - MAINTENANCE

Hydraulic oil

WARNING

Pressurized hydraulic fluid can penetrate the skin and cause severe injuries.
Hydraulic fluid is under extreme pressure. Rest the bucket or attachment on the ground. Shut the
engine off, turn the key on, and move the hydraulic control lever through all movements several times
to relieve residual pressure in the system.
Failure to comply could result in death or serious injury.

W0161A

Check the level of the hydraulic oil tank every 10 hours or each day.

Prior operation:

Keep all unauthorized personnel clear of the area. Park the machine on level ground, in neutral with the parking
brake applied, and the attachment lowered to the ground. Make sure that all residual pressure is relieved from circuits
before beginning maintenance.

Service specifications

Type of oil

T

UTELA

A

UTO

S

UPREME

™ E

NGINE OIL

SAE 10W-30

Total system capacity

210 L

(

55 US gal

)

Fluid level check

1. Before you start the engine, check the oil level in the

sight gauge. If the oil is cold, the level is correct when
the top of the oil is aligned with the indicator mark on
the sight gauge

(1)

.

2. If oil is required, make certain that all pressure is re-

lieved in the system.

RAIL13DOZ1686AA

1

3. Slowly loosen the tank cap

(2)

and top off until the

proper oil level is reached.

RAPH12DOZ0048AA

2

7-33

«
...
187
188
189
190
191
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов