manualshive.com logo in svg

Case 2050M, Руководство оператора, Страница: 167 / 286

Поделиться
Скачать
Case 2050M Скачать руководство пользователя страница 167

7 - MAINTENANCE

Releasing pressure in the hydraulic system

WARNING

Pressurized hydraulic fluid can penetrate the skin and cause severe injuries.
Hydraulic fluid is under extreme pressure. Rest the bucket or attachment on the ground. Shut the
engine off, turn the key on, and move the hydraulic control lever through all movements several times
to relieve residual pressure in the system.
Failure to comply could result in death or serious injury.

W0161A

WARNING

Escaping fluid!
Hydraulic fluid or diesel fuel leaking under pressure can penetrate the skin and cause infection or
other injury. To prevent personal injury: Relieve all pressure before disconnecting fluid lines or per-
forming work on the hydraulic system. Before applying pressure, make sure all connections are tight
and all components are in good condition. Never use your hand to check for suspected leaks under
pressure. Use a piece of cardboard or wood for this purpose. If injured by leaking fluid, see your
doctor immediately.
Failure to comply could result in death or serious injury.

W0178A

WARNING

Escaping fluid!
Do not disconnect hydraulic quick coupler under pressurized conditions. Make sure all hydraulic
pressure is removed from the system before disconnecting hydraulic quick coupler.
Failure to comply could result in death or serious injury.

W0095A

WARNING

Burn hazard!
Before performing any service on the hydraulic system, you must allow it to cool. Hydraulic fluid
temperature should not exceed 40 °C (104 °F).
Failure to comply could result in death or serious injury.

W0241A

7-11

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов