Case 2050M Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 286

Case 2050M Скачать руководство пользователя страница 137

6 - WORKING OPERATIONS

6 - WORKING OPERATIONS

###_6_###

GENERAL INFORMATION

Dozer blade

WARNING

Hazard to bystanders!
Always know the location of all workers in your area. Warn them before you start working on the
machine. Always keep all unauthorized bystanders clear of the area.
Failure to comply could result in death or serious injury.

W0176A

WARNING

Avoid injury!
Do not operate the machine while under the influence of alcohol or drugs.
Failure to comply could result in death or serious injury.

W0160A

WARNING

Improper operation or service of this machine can result in an accident.
Raised equipment or machine movement without an operator can cause serious injury. Always do the
following before performing any maintenance:
Park the machine on flat, level ground.
Lower the attachment to the ground.
Shut down the engine and remove the starter switch key.
Lock the tracks.
Failure to comply could result in death or serious injury.

W0269A

WARNING

IMPROPER OPERATION OF THIS MACHINE CAN CAUSE DEATH OR SERIOUS INJURY.
MAKE SURE THAT EVERY OPERATOR:
-learns and practices the safe use of machine controls in a safe, clear area before operating the ma-
chine on a job site.
-clears the work area of all bystanders.
-observes pertinent laws and regulations.
-follows the instructions in this operator's manual.
Failure to comply could result in death or serious injury.

W0189A

WARNING

Driving hazard!
Hillside operations can be dangerous. Rain, snow, ice, loose gravel, or soft ground, etc. can change
the ground conditions. You must make a judgment if it is safe to operate your machine on any hillside
or ramp.
Failure to comply could result in death or serious injury.

W0144A

WARNING

Hazard to bystanders!
Always sound the horn before starting the machine. Make sure the work area is clear of other persons,
domestic animals, tools, etc. before you operate the machine. Never allow anyone in the work area
during machine operation.
Failure to comply could result in death or serious injury.

W0304A

6-1

«
...
135
136
137
138
139
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов