Case 2050M Скачать руководство пользователя страница 217 | Manualshive

Страница: 217 / 286

Case 2050M Скачать руководство пользователя страница 217

7 - MAINTENANCE

Fuel filter

WARNING

Fire hazard!
When handling diesel fuel, observe the following precautions:
1. Do not smoke.
2. Never fill the tank when the engine is running.
3. Wipe up spilled fuel immediately.
Failure to comply could result in death or serious injury.

W0099A

Replace the fuel filter when the hour meter registers 500 hours. Fuel filters should be replaced every 500 hours
thereafter or more frequently when operating conditions are severe.

Prior operation:

Keep all unauthorized personnel clear of the area. Park the machine on level ground, in neutral with the parking
brake applied, and the attachment lowered to the ground. Make sure that all residual pressure is relieved from circuits
before beginning maintenance.

1. Locate the fuel filter in the right rear access compart-

ment. Close the fuel shut off valve

(1)

to prevent fuel

leakage.

2. Clean the fuel filter head, the outside of the fuel filter,

and remove any dirt and debris around the area that
might contaminate the system.

RAIL13DOZ1686AA

1

3. Turn the fuel filter

(2)

counterclockwise and remove.

Capture any fuel remaining in the lines or the fuel filter,
and discard properly.

4. Apply a thin layer of clean oil to the gasket on the new

fuel filter.

5. Install the filter. Use your hands to tighten the fuel filter

1/2 to 3/4 turn after the fuel filter makes contact with the
filter head.

6. Check for leaks.

RAIL13DOZ1699AA

2

NOTICE:

Never use a filter wrench to tighten a new fuel filter on install.

7-61

«
...
215
216
217
218
219
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов