manualshive.com logo in svg

Case 2050M, Руководство оператора, Страница: 235 / 286

Поделиться
Скачать
Case 2050M Скачать руководство пользователя страница 235

7 - MAINTENANCE

Hydraulic and hydrostatic drive filter and fluid

WARNING

Pressurized hydraulic fluid can penetrate the skin and cause severe injuries.
Hydraulic fluid is under extreme pressure. Rest the bucket or attachment on the ground. Shut the
engine off, turn the key on, and move the hydraulic control lever through all movements several times
to relieve residual pressure in the system.
Failure to comply could result in death or serious injury.

W0161A

Change the hydraulic/hydrostatic drive system oil and filters every 2000 hours of operation and every 2000 hours
thereafter. Change the oil more frequently when operating conditions are severe.

Prior operation:

Keep all unauthorized personnel clear of the area. Park the machine on level ground, in neutral with the parking
brake applied, and the attachment lowered to the ground. Make sure that all residual pressure is relieved from circuits
before beginning maintenance.

Service specifications

Type of oil

T

UTELA

A

UTO

S

UPREME

™ E

NGINE OIL

SAE 10W-30

Total system capacity

210 L

(

55 US gal

)

1. Stop the engine. Put a Do Not Operate tag on the key

switch.

2. Make sure the accumulators on the machine are com-

pletely discharged.

3. Clean the area around the hydraulic oil filler cap, and

slowly loosen the cap.

RAPH12DOZ128AA

1

4. Remove the bolts and the cover plate from the rear of

the machine.

RAIL13DOZ1266AA

2

7-79

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов