Case 2050M Скачать руководство пользователя страница 27

Страница: 27 / 286

2 - SAFETY INFORMATION

If the operator presence system is inoperable, then it must be repaired.

Seat belts

Seat belts must be worn at all times.

Seat belt inspection and maintenance:

• Keep seat belts in good condition.

• Keep sharp edges and items than can cause damage away from the belts.

• Periodically check belts, buckles, retractors, tethers, slack take-up system, and mounting bolts for damage and

wear.

• Replace all parts that have damage or wear.

• Replace belts that have cuts that can make the belt weak.

• Check that bolts are tight on the seat bracket or mounting.

• If the belt is attached to the seat, make sure that the seat or seat brackets are mounted securely.

• Keep seat belts clean and dry.

• Clean belts only with soap solution and warm water.

• Do not use bleach or dye on the belts because this can make the belts weak.

Pull the right-hand belt from the seat belt retractor. Fasten
the metal belt end into the left-hand buckle.

RCIL10CWL037AAL

Press the red button on the left-hand seat belt mechanism
to release the seat belt.

RCIL10CWL083FAL

2-5

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 27 / 286

Результаты поиска

Содержание 2050M

Отзывы: