manualshive.com logo in svg

Case 2050M, Руководство оператора, Страница: 122 / 286

Поделиться
Скачать
Case 2050M Скачать руководство пользователя страница 122

4 - OPERATING INSTRUCTIONS

Deceleration or transmission pedal

The machine features a dual function deceleration or
transmission pedal. The transmission (Trans) pedal is
the default feature. Use the deceleration pedal to slow or
stop the vehicle for precision grading. The deceleration
pedal reduces the throttle setting as it is depressed. The
deceleration pedal works in any direction. The function
of the pedal can be changed through the multi-function
display. See complete multi-function display instructions
and changing the pedal functions in this chapter on page

4-15

.

NOTICE:

See the deceleration/transmission safety sign

located above the pedal and in the safety section in this
manual.

RAIL13DOZ1264AA

1

47449566

2

Throttle speed lever

1. Pull the throttle speed lever back to increase the en-

gine speed.

2. Push the throttle speed lever forward to decrease the

engine speed.

NOTICE:

Run the engine at low idle for a few minutes be-

fore turning the engine off. Always shut the engine down
with the throttle at its lowest setting to keep from damag-
ing the turbocharger.

RAPH12DOZ0080AA

3

4-20

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов