Case 2050M Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 286

Case 2050M Скачать руководство пользователя страница 41

2 - SAFETY INFORMATION

WARNING — Crush hazard

RAPH12DOZ0062AA

14

This WARNING safety sign is located on the right-hand
side of the machine above the tracks.
WARNING — Improper lifting or tiedowns can allow load
to shift and cause injury or damage. Failure to comply
with this warning could result in death or serious injury.
English safety sign number: 87416964

87416964

15

WARNING — Pressurized system hazard

RAIL13DOZ1686AA

16

This WARNING safety sign is located inside the right
rear service compartment.
WARNING — Pressurized system hazard. Relieve
pressure before maintenance. Precharge only with dry
inert gas such as high purity nitrogen. Failure to comply
with this warning could result in death or serious injury.
English safety sign number: 384260A1
French safety sign number: 328903A1
Spanish safety sign number: 328903A1

384260A1

17

2-19

«
...
39
40
41
42
43
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов