Case 2050M Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 286

Case 2050M Скачать руководство пользователя страница 123

5 - TRANSPORT OPERATIONS

5 - TRANSPORT OPERATIONS

###_5_###

ROAD TRANSPORT

Tow procedure

WARNING

Misuse hazard!
Towing is a delicate maneuver that is always carried out at the risk of the user. The manufacturer's
warranty does not apply to incidents or accidents that occur during towing. Where possible, carry out
the repairs at the site.
Failure to comply could result in death or serious injury.

W0286A

WARNING

Transport hazard!
Make sure that the weight of a trailed vehicle that is not equipped with brakes NEVER EXCEEDS the
weight of the machine that is towing the vehicle. Stopping distance increases with increasing speed
as the weight of the towed load increases, especially on hills and slopes.
Failure to comply could result in death or serious injury.

W1138A

NOTICE:

If you doubt your ability to perform this procedure, contact your authorized dealer. This procedure will

require removing the floor mat and seat bolts.

Engine or hydraulic failure

Towing this machine is not recommended. If your machine is disabled, you must make a judgment if the machine can
be moved without further damage. If possible, repair the machine at the job location.
If you cannot repair the machine at the job location, you may wish to contact your authorized dealer for assistance.
Incorrectly performed towing procedures can severely damage machines with hydrostatic motors.
Keep all unauthorized personnel clear of the area.

1. Use the multi-function display screen to select the tow-

ing mode. From the main menu, scroll down and se-
lect “Service”. Press the enter switch.

RAIL15DOZ0018AA

1

5-1

«
...
121
122
123
124
125
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов