manualshive.com logo in svg

Case 2050M, Руководство оператора, Страница: 254 / 286

Поделиться
Скачать
Case 2050M Скачать руководство пользователя страница 254

7 - MAINTENANCE

Ripper shanks and teeth

WARNING

Flying object!
Always wear eye or full face protection when performing this procedure.
Failure to comply could result in death or serious injury.

W0313A

Ripper shanks or ripper teeth may require periodic replacement. Use care when lifting heavy objects. Always use
adequate lifting equipment.

Prior operation:

Keep all unauthorized personnel clear of the area. Park the machine on level ground, in neutral with the parking
brake applied, and the attachment lowered to the ground. Make sure that all residual pressure is relieved from circuits
before beginning maintenance.

1. The ripper shanks have a threaded orifice for lifting.

Insert an I-bolt of adequate size when changing ripper
shanks.

RAIL12DOZ0371AA

1

2.

CAUTION

Heavy object!
The component is heavy. Use care not to drop
the component when installing, removing, or
handling.
Failure to comply could result in minor or mod-
erate injury.

C0095A

Use proper and adequate lifting equipment and lift the
ripper shanks.

RAIL12DOZ0370AA

2

7-98

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов