Case 2050M Скачать руководство пользователя страница 175

Страница: 175 / 286

7 - MAINTENANCE

General specification - Diesel fuel

Only use diesel fuel that conforms to North American
standard

ASTM D975

Grade No. 2-D S15 or equivalent

in your engine. Do not use any other low grade diesel
fuel.

NOTICE:

Use of other low grade diesel fuels will result in

loss of engine power, high fuel consumption, and damage
to the exhaust aftertreatment system (if equipped).

NOTE:

When operating the machine in very cold climates,

the use of winter blended fuel is permitted for a short pe-
riod of time. See your fuel supplier for winter fuel require-
ments in your area.

Fuel conditioner

Diesel fuel conditioner is available from your CASE CON-
STRUCTION dealer. Instructions for the use of the fuel
conditioner is on the container.

The use of diesel fuel conditioner will:

• Clean fuel injectors, valves, and manifolds for in-

creased service life

• Disperse insoluble gummy deposits that form in the fuel

system

• Separate moisture from the fuel

• Stabilize fuel in storage

NOTICE:

Use only CASE CONSTRUCTION approved

biocide additives to prevent damage to the exhaust af-
tertreatment system (if equipped).

7-19

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 175 / 286

Результаты поиска

Содержание 2050M

Отзывы: