Case 2050M Скачать руководство пользователя страница 140

Страница: 140 / 286

6 - WORKING OPERATIONS

Bulldozer blade adjustment (if equipped)

Bulldozer blade — Tilt centering

1. Set the bulldozer blade on a level surface. Make sure

the blade is even when it rests on the ground.

2. Raise the blade off of the ground high enough so that

the blade does not hit the ground when fully tilted right
or left.

(A)

is roughly

457.2 mm

(

18.0 in

) off the ground.

RAIL14DOZ0525AA

3. Place a digital angle gauge

(B)

on the top of the blade,

and zero out the gauge.

NOTE:

The gauge must read in tenths, i.e. in

0.1 °

incre-

ments.

RAIL14DOZ0526AA

4. Remove and retain the bolts

(C)

on the left-hand pitch

link

(D)

to allow for adjustment of the pitch angle.

RAIL14DOZ0529AA

6-4

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 140 / 286

Результаты поиска

Содержание 2050M

Отзывы: