Case 2050M Скачать руководство пользователя страница 256 | Manualshive

Страница: 256 / 286

Case 2050M Скачать руководство пользователя страница 256

7 - MAINTENANCE

Battery service

WARNING

Electrical shock hazard!
Do not reverse battery terminals. Connect positive cable ends to positive terminals (+) and negative
cable ends to negative terminals (-).
Failure to comply could result in death or serious injury.

W0262A

WARNING

Improper operation or service of this machine can result in an accident.
Before working on any component(s) of the electrical circuit, put the starter switch key in the off (shut
down) position. When disconnecting batteries, always disconnect the negative (-) cable first. When
reconnecting batteries, always connect the negative (-) cable last.
Failure to comply could result in death or serious injury.

W0264A

WARNING

Hazardous chemicals!
Battery electrolyte contains sulfuric acid. Contact with skin and eyes could result in severe irritation
and burns. Always wear splash-proof goggles and protective clothing (gloves and aprons). Wash
hands after handling.
Failure to comply could result in death or serious injury.

W0006A

WARNING

Battery acid causes burns. Batteries contain sulfuric acid.
Avoid contact with skin, eyes or clothing. Antidote (external): Flush with water. Antidote (eyes): flush
with water for 15 minutes and seek medical attention immediately. Antidote (internal): Drink large
quantities of water or milk. Do not induce vomiting. Seek medical attention immediately.
Failure to comply could result in death or serious injury.

W0111A

WARNING

Electrical shock hazard!
Before working on any part of the electrical system, disconnect the battery ground cable. Complete
all electrical work before connecting the cable.
Failure to comply could result in death or serious injury.

W0129A

WARNING

Explosion hazard!
If battery electrolyte is frozen, attempting to charge the battery or jump-start the engine can cause the
battery to explode. Always keep batteries at full charge to prevent frozen battery electrolyte. Never
charge a frozen battery.
Failure to comply could result in death or serious injury.

W0203A

WARNING

Chemical hazard!
Battery posts, terminals, and related accessories contain lead and lead compounds. Wash hands after
handling.
Failure to comply could result in death or serious injury.

W0349A

7-100

«
...
254
255
256
257
258
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов