Case 2050M Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 286

Case 2050M Скачать руководство пользователя страница 134

5 - TRANSPORT OPERATIONS

PREPARING FOR ROAD TRANSPORT

Lifting the machine

WARNING

Crushing hazard!
Always remove the attachment before lifting the machine.
Failure to comply could result in death or serious injury.

W1195A

DANGER

Avoid injury!
The machine can tilt forward or backward. Leave the lifting straps attached in order to secure the
machine.
Failure to comply will result in death or serious injury.

D0110A

WARNING

Crushing hazard!
The lifting systems must be operated by qualified personnel who are aware of the correct procedures
to follow. Make sure all lifting equipment is in good condition, and all hooks are equipped with safety
latches.
Failure to comply could result in death or serious injury.

W0256A

Lifting hooks

Lift the machine using the lifting attachment

points identified on the machine by the lift hook symbol.

NOTE:

See the Lift Safety Signs located on each side of the machine.

1. Keep all unauthorized personnel clear of the area. Do

not allow anyone on the machine while it is being lifted.

2. Remove any loose items, tools, etc. and lock all doors.

3. Use lifting equipment of sufficient weight lifting capac-

ity for this machine. Shield the machine with cloth or
pads to protect finish.

4. Position the machine so the center of gravity balances

the machine.

5. Lift the machine slightly, and allow it to balance and

stabilize before continuing lift.

RAPH12DOZ0062AA

1

5-12

«
...
132
133
134
135
136
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов