Case 2050M Скачать руководство пользователя страница 278

Страница: 278 / 286

8 - SPECIFICATIONS

Ripper specifications

Operating data and dimension - Ripper

Tractor model

PAT blade

BD blade

Overall length in transport position

6580.4 mm

(

259.1 in

)

6475.9 mm

(

255 in

)

Overall length with ripper shank resting on the ground line

6956.5 mm

(

273.9 in

)

6852 mm

(

269.8 in

)

Ripper shanks in top position

Lift

Dig

486 mm

(

19.1 in

)

507 mm

(

20 in

)

Ripper shank in mid position

Lift

Dig

570 mm

(

22.4 in

)

422 mm

(

16.6 in

)

Ripper shank in bottom position

Lift

Dig

655 mm

(

25.8 in

)

337 mm

(

13.3 in

)

Type of control

Hydraulic cylinders — double acting

Overall width (Maximum)

1953.3 mm

(

76.9 in

)

Width of cut (Maximum)

1889.8 mm

(

74.4 in

)

Number of teeth (Standard)

Number of teeth (Maximum)

Shank width

50.8 mm

(

2.0 in

)

Tooth width

66.0 mm

(

2.6 in

)

NOTE:

Lift and dig dimensions are with the grouser fully penetrated. Add

52.6 mm

(

2.07 in

) if unit is on solid surface.

8-8

Содержание 2050M































































































































































































































































































Результаты поиска

Содержание 2050M

Отзывы:

Case 2050M, Руководство оператора, Страница: 278 / 286

Результаты поиска

Содержание 2050M

Отзывы: