manualshive.com logo in svg

Case 2050M, Руководство оператора, Страница: 200 / 286

Поделиться
Скачать
Case 2050M Скачать руководство пользователя страница 200

7 - MAINTENANCE

Every 50 hours

Fuel pre-filter - Drain condensation

WARNING

Fuel vapors are explosive and flammable.
Do not smoke while handling fuel. Keep fuel away from flames or sparks. Shut off engine and remove
key before servicing. Always work in a well-ventilated area. Clean up spilled fuel immediately.
Failure to comply could result in death or serious injury.

W0904A

Drain water and sediment from the fuel filter every 50 hours and every 50 thereafter or more often if conditions so
require or if fuel quality is poor.

Prior operation:

Keep all unauthorized personnel clear of the area. Park the machine on level ground, in neutral with the parking brake
applied and the attachment lowered to the ground. Make sure that all residual pressure is relieved from circuits before
beginning maintenance.

Drain fuel filter condensation

1. Locate the fuel filter

(1)

on the right side of the machine.

2. Open the drain valve on the bottom of the fuel filter by

turning counterclockwise two or three turns.

3. Drain the water and/or contaminants from the fuel pre-

filter into a suitable container until clean fuel flows. Do
not allow fuel to spill on engine or ground.

4. Tighten the drain valve only finger tight, turning clock-

wise.

5. Check for leaks.

RAIL13DOZ1699AA

1

7-44

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов