manualshive.com logo in svg

Case 2050M, Руководство оператора, Страница: 260 / 286

Поделиться
Скачать
Case 2050M Скачать руководство пользователя страница 260

7 - MAINTENANCE

Battery removal and installation

CAUTION

Heavy parts!
Machine batteries are extremely heavy. Make sure the battery is supported safely during the removal
process.
Failure to comply could result in minor or moderate injury.

C0050A

WARNING

Chemical hazard!
When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to spill
through the vent caps. Lift a plastic-cased battery with a battery carrier or with your hands positioned
on opposite corners of the battery. Always wash your hands after handling.
Failure to comply could result in death or serious injury.

W0385A

Prior operation:

Keep all unauthorized personnel clear of the area. Park the machine on level ground, in neutral with the parking
brake applied, and the attachment lowered to the ground. Make sure that all residual pressure is relieved from circuits
before beginning maintenance.

Replacing the battery

1. Turn the electronic disconnect switch to the OFF posi-

tion.

RAIL13DOZ1702AA

1

7-104

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов