Case 2050M Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 286

Case 2050M Скачать руководство пользователя страница 37

2 - SAFETY INFORMATION

Safety signs

WARNING

Avoid injury!
An illegible or missing safety sign can have far-reaching consequences. Inspect safety signs daily.
Clean and replace damaged safety signs as necessary.
Failure to comply could result in death or serious injury.

W0167A

The following safety signs are on your machine as a guide for your safety and for the safety of those working with you.
Walk around the machine and note the content and the location of all safety signs before you operate your machine.

Keep all safety signs clean and legible. Clean safety signs with a soft cloth, water, and a gentle detergent.

NOTICE:

Do not use solvent, gasoline, or other harsh chemicals. Solvents, gasoline, and other harsh chemicals may

damage or remove safety signs.

Replace all safety signs that are damaged, missing, painted over, or illegible. If a safety sign is on a part you or
your dealer replaces, make sure that you our your dealer install the safety sign on the new part. See your dealer for
replacement safety signs.

Safety signs that display the “Read operator’s manual” symbol direct you to the operator’s manual
for further information regarding maintenance, adjustments, or procedures for particular areas of the
machine. When a safety sign displays this symbol, consult the appropriate page of the operator’s
manual.
Safety signs that display the “Read service manual” symbol direct you to the service manual. If you
doubt your ability to perform service operations, contact your dealer.

2-15

«
...
35
36
37
38
39
...
»

Содержание 2050M































































































































































































































































































Отзывы:

Нет отзывов